Either by right clicking on the Mac OS X 10.9 object on the left side panel or via the tabbed window. Go to Edit virtual machine settings. Select the Mac OS X 10.9.vmx file and select Open. Run VMware Workstation or VMware Player and select Open a Virtual Machine.The window opens and closes immediately. Well after I ran the win-install.cmd nothing happens. Godmax Decemat 5:49 AM Reply. It’s no working well on VMware Player 14 but it works on VMware 12.
Osx On Vmware Player Download And Extract2: Download and extract VMWare macOS Unlocker. 1: Install VMWare in the usual way. It’s $29 and you get the original media (which is always good to have on hand).Basic setup. Please purchase your copy of Mac OS X desktop software from Apple. Mukhtar Jafari Post author Decemat 10:57 AM ReplyWith this article, I’ll start by saying.![]() Vmx file mentioned just above and open it. If you absolutely feel you want to reinvent, then I’ll leave that for you to determine what’s necessary.To begin, inside VMWare Player, select File->Open a Virtual Machine. So, use what’s given rather than trying to reinvent the wheel. It’s far simpler to use their existing template than trying to figure out all the proper VMWare Player settings. Note, you’ll need to use this template to get the install going. Once the machine has started and the system begins searching for a CDROM (read the text on the screen), you will need to change the CDROM to the Mac OS X Snow Leopard media. So, click ‘Play Virtual Machine’. Click ‘OK’.You’re now ready to boot. Now click the on the CDROM device and under ‘Connection’ change it to ‘Use ISO image’ and browse to and select the darwin_snow.iso image inside the Snowy_VM directory’. Choose the ‘Mac OS X Server 10.6 (experimental)’ imported machine and choose ‘Edit virtual machine settings’ on the bottom right of the window. From here, you will need to modify the settings for the CDROM device under this machine. Follow the steps to install Mac OS X. Once the install begins, you are now installing Mac OS X. Check the box next to ‘Connected’ at the top of the window and click ‘OK’ at the bottom.The system should recognize the disk change and begin to boot the media in about 10 seconds. Locate the Snow Leopard media on your hard drive and click ‘OK’ to accept it. At the bottom of the active VM Window, right click the CDROM icon which may now be greyed out (disconnected) and choose ‘Settings’. So, I will assume you are using an ISO image here. There are two behaviors you should watch for. When you reboot the first time, the system may or may not boot up. So you don’t need to format it.Booting issues with VMWare Player and Mac OS XLet’s pause and explain this. Note the hard drive given in this Snowy_VM archive is ‘ready to go’. This way, you leave one CDROM always set up with darwin_snow.iso and you use the second one to load/unload other ISO images. Perhaps they can create a standalone booter later, but for now this works.Note, I recommend setting up a second CDROM drive inside your Mac OS X virtual machine’s settings. Leaving it in the drive is really not a problem as it boots up so quickly. So, we live with these issues.The third issue is that you will need to continually leave the darwin_snow.iso image in the drive all of the time to boot up Mac OS X. If you see this, you will need to reboot and try again.These issues are annoying, but that’s why this is ‘experimental’. If it never progresses beyond this grey screen, then you will need to reboot and try again.The second behavior is that it may get past the grey screen, but then Finder never appears and you see a forever spinning cursor. Note that the sound and display drivers are just about as good as what’s in Virtual Box. At this point, you might want to change things like Sound and Display. After going through all of the registration screens you will be at the standard Finder desktop. So, this is why I recommend setting up a second drive for loading ISO images.After getting through any unsuccessful boot attempts (or not), you should get to the registration screen. If you don’t do this, Mac OS X won’t boot. Note that if you change the darwin_snow.iso image to something else, you have to remember to set it back when you’re done. Photomatix pro for mac os x serialUnder ‘Monitors’ change it to ‘Specify Monitor Settings’ and manually change the maximum resolution to ‘1366×768’. Once you have done this, edit the virtual machine in VMWare player and choose the Display setup. Add in the lines related to the graphics. So, don’t expect a whole lot here.Suffice it to say that you will need to follow editing of the apple.com.Boot.plist file as in the ‘ Installing Mac OS X on VirtualBox‘ article on Randosity. ![]() The trick is in getting this into the Mac. But, your mileage may go farther. I have tried installing this without success. The setup for VirtualBox is a little more complex, but it boots consistently every time, has its own standalone boot loader and offers a few more features.If you have questions, please leave a comment below.Yes, it should be fine just to keep rebooting it until it starts up. Good luck and happy installing.If you’re looking for something that boots consistently for Mac OS X, has better video mode support and working sound, then I would suggest setting up Mac OS X on VirtualBox. Hopefully this booting issue will be fixed at some point. You may run into the booting issues from time to time, just reboot until it boots up. Then extract it, find this file and install it.At this point, you should be all set. Snapshots work best if you intend to work on the VM and save files to it. Then, if one of the resets happens to corrupt the Mac’s drive, you can easily restore to a previously known working copy. However, if you are concerned that it could become a problem, I’d suggest taking a snapshot (or make a copy) of the VM. I haven’t had a problem with hard booting (aka reset) until it works. I do not fully understand what the issue is, but it may have something to do with certain kernel drivers being loaded and the timings of them. But it shouldn’t be a problem to reset it several times in a row to get it working on a recently launched copy of VMWare Player. That said, though, there may be bugs in VMWare player that could present after a number of reboots if you leave it running constantly. Resetting it should be enough.
0 Comments
Leave a Reply. |
AuthorYolanda ArchivesCategories |